Ladder Leveler - Permanent Mount Style by Levelok

Level your ladder in less than five seconds!

The patented LeveLok® LL-STB-1 Leveler/Stabilizer has only two controls, and operating it is so easy,
it can be done with the touch of a toe.

This permanent mount style ladder leveler can stabilize virtually any ladder: aluminum or fiberglass, extension,
combination, articulating, double-sided step, or sectional. Installs easily and quickly to adapt to nearly any indoor
or outdoor situation, from stairwells to uneven terrain on job sites. Simple and easy to put together: attaches to
ladder rail with 3 mounting bolts, fender washers and nylon locking nuts.

LeveLok is the choice of major U.S. and Canadian utility companies.

Super heavy duty construction
6061-T6 Aluminum
Stainless steel locking system
Fully automatic safety lock
Only two controls -- operating is so easy, it can be done with the touch of a toe!
Extends a full 10"
Automatic back-up safety lock
Snap on / off polypropylene cap
Meets or exceeds OSHA/ANSI requirements up to and including type 1AA (375lbs) ladders

Each kit contains:   
•    2 Ladder Levelers    
•    Installation Hardware     
•    Instruction Manual   
•    Template  

Ergonomic Shapes
•    Foot pedal snaps up for storage or down for leveling
•    Curved shapes for ease of grip and leveling comfort
•    Grooved surfaces of upper and lower pedals provide easy to grip surfaces
•    Foot pedal can actually be snapped up and down with toe of shoe or boot\

Leveler Shoes
• These shoes are heavy duty, made of steel that swivels front to back and side to side
• Rubber tread secured with 3 extra-wide fasteners
• Triple plated pivoting foot with claw flips back for ice, snow, or gravel
• Large, heavy duty anti-skid rubber treads on claw-pivoting foot -- grips almost any surface

Quick and Simple Installation
• Place template on ladder rail
• Drill 3 holes using template as drill guide
• Slide leveler into holes
• Tighten locknuts
• Mounting bolts are pre-installed to prevent fumbling around with bolts

To Level -To set into position, hold the ladder with both hands and simply push the foot pedal down. The leg will extend in increments of 3/16 of an inch up
to 9-3/4". You'll hear the stainless steel ratchet's reassuring "click" with each increment. When the leg has been extended to the point where it
has firm footing, you're done!

The automatic safety lock instantly engages, thereby providing a back-up safety lock, preventing the possibility of accidental tripping of the locking mechanism. This is another unique and patented feature found only on Levelok Ladder Leveling Systems.

To Release - While the ladder is still in the rested position with both hands on ladder, simply pull the ladder rail with the extended leveler back toward you to remove the weight from the ladder leg. Then depress upper release lever with ball of foot or thumb and the spring tension will slowly retract the inner leg all the way up, until it stops against the bumpers. The ladder can now be relocated and leveled again. The Ladder Leveler (Permanent Mount Style) contains a pair of levelers which permanently mount to each leg of your ladder, hardware, template and instructions.

*Model LL-STB-1AL For most standard extension, combination and articulating ladders with a rail thickness between 1/8" and 3/8" thick. Not for sectional, wood or other types of ladders with thick or box beam rails. If you would like to order the LL-STB-1SL, which fits up to a 15/16" rail thickness, please call us to special order.

Standards Compliance - Meets all ANSI and OSHA requirements for ladders up to Type 1AA, 375 pound duty rating;
exceeds OSHA Directive 1-1.14 and ANSI A14.10 Standard for Type 1AA

Ladder Compatibility - Fits most aluminum and fiberglass, extension, combination, articulating, or sectional ladders.

Mounting Bolt Length - 7/8 inch  

Installation Method - Attaches to ladder rail with 3 mounting bolts, fender washers and nylon locking nuts.  

Locking System - Stainless steel, double-row ratchet teeth, precision cut for precise 3/16" incremental adjustments.  

Safety Lock - Patented, fully automatic, stainless steel, anti-trip, back-up safety lock.  

Weight per unit -  Each individual ladder leveler weighs  5 lbs 2 oz.

Shipping Weight -  12 lbs. 1 oz. for each complete kit, including 2 levelers, hardware kit, template, etc.

Warranty - 12 months parts and labor for manufacturing defects.